Draper VIC-12 Betriebsanleitung PDF herunterladen

Installation/Operating Instructions

Access XL 220V Electric Projection Screen by Draper

Hanging Screen

When locating viewing surface and checking clear ance for screen operation,

remember surface is centered in the length of the case. Regardless of mounting

method used, the following points apply:

① Engage each ceiling mounting bracket with top of housing as shown below and

tighten nuts. The outer two brackets should be centered above the location of

the interior roller brackets (+/-102mm). The remaining two brackets should be

equally spaced between the outermost brackets.

② Screen should be lifted into position only by the outermost ceiling mounting

brackets (those on ends). Keep case level by lifting each end simul-

taneously to prevent surface damage. Never attempt to lift screen along

its length.

③ The entire weight of the unit MUST BE supported by the outermost mounting

brackets to provide a secure installation (those on ends). Do not use

intermediate brackets to lift or support the weight of the screen.

④ Screen should be positively and securely supported so that vibration or even

abusive pulling on viewing surface will not weaken installation.

⑤ Installer must insure that fasteners used are of adequate strength and

suitable for the mounting surface chosen. Installer must also insure that

Electrical Con nec tions

Screen operates on 220V, 50 Hz., 1ph with max 2.1 amp current draw.

Junction box is lo cat ed just above the bottom access panel at left end of screen

(stan dard, right end may be speciﬁ ed). Remove the bottom access panel for

access to the junction box cover. (See Bottom Access Panel Removal instructions

below.) Remove four (4) hex head screws that secure the cover to the junction box

to expose the black, brown and blue pigtail leads and the green/yellow ground wire

per wiring diagram on page 4.

If optional low voltage control or video interface control is speciﬁ ed and factory

installed, please refer to wiring diagrams on page 5.

Screen is shipped with internal wiring complete and control switch (es) fully boxed.

Wire to connect screen to switch (es) and switch (es) to power supply should be

furnished by installer. Con nec tions must be made in ac cor dance with attached

wiring diagram, and wiring must comply with national and local electrical

codes.

All operating switches should be “off” before power is connected.

Bottom Access Panel Installation/Removal

Removal and replacement of the bottom closure panel requires two people

positioned about 152cm from each end of the panel.

① Before removing bottom closure, you must ﬁ rst remove screws at each

end of case and slide the closure clips inward, away from the outside of

the case (see Fig. 3).

If you encounter any difﬁ culties installing or ser vic ing your Access XL screen, call your

dealer or Draper, Inc., in Spiceland, Indiana, 765/987-7999 or fax 765/987-7142.

Suitable for use in environmental air space in accordance with Section

300-22(c) of the National Electrical Code, and Sections 2-128, 12-010(3)

and 12-100 of the Canadian Electrical Code, Part 1, CSA C22.1.

Typical

Installation

Alternate

Installation

(additional set of

brackets required

but not included).

Two intermediate

brackets must be

spaced evenly

from ends.

Slots along top of case

permit brackets to be

set at an angle

Case dimensions

on page 3.

Caution

① Read instructions through completely before proceeding.

② Follow instructions carefully. Installation con trary to in struc tions

invalidates warranty.

③ Pick up screen case from ends only. Picking case up at other points will

damage case and may damage fabric.

④ To insure a safe installation, the entire weight of the unit MUST BE

supported by outermost ceiling mounting brackets (those on ends). Don't

use intermediate brackets to lift or support the weight of the screen.

⑤ To eliminate the possibility of the case warping, outermost ceiling

mounting brackets (those on ends) must be located centered above

the interior roller mounting brackets (+/-102mm).

⑥ Entire bottom of screen case should be unobstructed to permit access to

bottom panel for making electrical connections or servicing.

⑦ Screen should be installed level (using a carpenter’s level).

⑧ Operating switch(es) packed separately in screen carton. Do not discard

with packing material.

⑨ An appropriate disconnect device shall be provided as part of the building

installation.

⑩ Screen operates on 220V, 50 Hz., 1ph. with max 2.1 amp draw.

NOTE: Screen has been thoroughly inspected and tested at factory and found to

be operating properly prior to shipment.

ceiling structure is of adequate strength. Supporting hardware (chains,

cables, 9.5mm rods, etc.) must be essentially vertical.

⑥ Entire bottom of case must be readily accessible after in stal la tion is complete.

⑦ Front, back and top of case must be straight—not forced to warp or bow

(see note 5 in caution box).

⑧ Do not use case to support adjacent sections of ceiling.

⑨ If case is painted on location, removal of roller/fabric assembly is recommended

prior to painting. If not removed, slot on bottom of case should be shield ed to

protect view ing surface from paint splatters or overspray.

⑩ Do not seal unit in ceiling until elec tri cal con nec tions have been made and

screen has been op er at ed successfully.

Dowel

Shipping

Bracket

Shipping Brackets

If provided, remove shipping brackets by following Figure 2.

Figure 2

Series V

Closure

Case

Figure 3

Continued on next page

Front of case

removed for

clarity

Motor Type Duty Cycle

506S2PA, 510S2PA, 515S2PA, 1 minute on, 3 minutes off

506S2 ILT2, 515S2 ILT2

525A2PA, 535A2PA, 535A2 ILT2 1 minute on, 10 minutes off

NOTE: Excessive continuous operation may cause the motor to over

heat. If this happens the motor will shut off until it cools to a normal

operating temperature.

These Installation/Operating Instructions are available in the ofﬁ cial language of

the country where you purchase the product. Please contact your distributor to

request a copy.

Vous pourriez demander les instructions d’installation et d’opération traduises

dans la langue ofﬁ cielle du pays ou vous achetez le produit. Veuillez demander à

votre distributeur.

Die Gebrauchsanweisung für Installation und Konstruktion sind in der ofﬁ ziellen

Sprache des Landes, indem Sie das Produkt gekauft haben, vorhanden. Fragen

Sie die jeweilige Verkaufs-Abteilung.

US Patent Nos. 6,137,629; 6,421,175; 6,532,109; 6,816,308; 7,559,707

" electrical cutout

1 2 3 4 5

Inhaltsverzeichnis

Seite 1 - Continued on next page

Seite 2 - page 2 of 5

Accessory Access ACXLE & ACXLV Roller InstallationPlease note: When ordering a motor with built-in Low Voltage Controller, if the case ships separ

Seite 3 - page 3 of 5

Access XL 220 Volt Instructions by Draper page 3 of 5Limit Adjustments (Standard Motor)Please Note: Screen limits are factory set for optimum perform

Seite 4 - Case Dimensions

Access XL 220 Volt Instructions by Draper page 4 of 5Case Dimensions*These wiring diagrams are for Access XL screens with motor on audi-ence left (st

Seite 5 - Mounting Bracket Dimensions

Access XL 220 Volt Instructions by Draper page 5 of 5*These wiring diagrams are for Access XL screens with motor on audience left (standard), and fab

Weitere Dokumente für Projektionswände Draper VIC-12

Um das Dokument anzuzeigen Draper VIC-12 Betriebsanleitung

Draper VIC-12 Betriebsanleitung (4 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Draper VIC-12 Betriebsanleitung

Stöbern Sie online oder laden Sie Betriebsanleitung nach Projektionswände Draper VIC-12 herunter. Draper VIC-12 Operating instructions Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Projektionswände Draper VIC-12

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Projektionswände Draper VIC-12