Draper Inc., Motorized Flexshade HandbookTable of Contents1. Introduction To Motorized Shades ...
Radio Remote Control Motor Programming Instructions When you receive a radio remote control motor from Draper, Inc., the motor has no programming on
Motor Name: 510S1RH RPM: 38 Volts: 230 Amps: 1.3 Min. Shade Width: 25” om With Crank override 30” om Standard Motor Lead Length: 6’ Lead
Motor Name: 503S1RH-ST RPM: 32 Volts: 230 Amps: .95 Min. Shade Width: 32” om With Crank Override 37” om Standard Motor Lead Length: 6’ L
Motor Name: 506S1PA RPM: 38 Volts: 230 Amps: .95 Min. Shade Width: 36” om Standard Motor Lead Length: 6’ Lead Type:
Motor Name: 510S1PA RPM: 38 Volts: 230 Amps:1.3 Min. Shade Width: 36” om Standard Motor Lead Length: 6’ Lead Type:
Motor Name: 660R2 RPM: 14 Volts: 120 Amps: 2.5 Min. Shade Width: 48” om Standard Motor Lead Length: n/a Lead Type:
Motor Name: ST-30 RPM: 28 Volts: 24VDC Amps: 1.8 Min. Shade Width: Standard Motor Lead Length: 15’ Lead Type: 22-2, awg/conductor Limit
Motor Name: BA-RTS RPM: 27 Volts: 12 V Amps: n/a Min. Shade Width: Standard Motor Lead Length: n/a Lead Type: n/a Limit Type:
Minimum Shade Sizes®Motorized 24" OM (241/8" IM) 506 Motorized shade regular motor in 2" roller (Dual 241/8" OM -24¼" 1M)
The following is for coupled shades 27" OM (271/16" IM -we take a 1/16" off the left & right panel to equal a total 1/8" IM
Installation InstructionsMotorized FlexShade by DraperCopyright © 2008 Draper Inc. Form MotorizedFlexShade_Inst08-R Printed in U.S.A.Mounting Bracke
RTS Dry Contact InterfaceOperating InstructionsThe RTS Dry Contact Interface can be used to communicate between home automation or other third party s
Motorized FlexShades by DraperPage 2 of 2NOTE: Test shade operation. If shade direction does not correspond with the switch orientation, turn power b
Installation InstructionsFlexShade 2 by DraperCopyright © 2007 Draper Inc. FormFlexShade2_Inst07-R2 Printed in U.S.A.Mounting Brackets and Endcaps➀
Push-Button Limit Switches:➀ Fully depress both limit switch push buttons, then operate wall switch to make sure system works properly.➁ Raise shade
Caution ➀ Read instructions through completely before proceeding. ➁ Follow instructions carefully. Installation con trary to in struc tions invali-
Dimensions*Colossal FlexShade by DraperPage 2 of 2Wiring DiagramsBottom Closure Removal/ReplacementStep 1Step 2Step 3Step 4Step 5Removal and replaceme
Red—NormallyopenBlue—Normally closedBlack—CommonTo 12V DC switched outlet(i.e. Projector)-Brown+OrangeWiring by InstallerToleranceDownDraper, Inc.411
To Station-BedInterface(this interface isnot sold by Draper)Wiring by InstallerToleranceDownDraper, Inc.411 S. Pearl St.Spiceland, IN 47385TitleScale
Multiple-Station Control(SS-4R) 1p3T, MomentaryWiring by InstallerToleranceDownDraper, Inc.411 S. Pearl St.Spiceland, IN 47385TitleScaleByDate DWG No
To Home AutomationCrestron, AMX, Etc.Wiring by InstallerToleranceDownDraper, Inc.411 S. Pearl St.Spiceland, IN 47385TitleScaleByDate DWG No.IntelliFl
ToleranceDownDraper, Inc.411 S. Pearl St.Spiceland, IN 47385TitleScaleByDate DWG No.RS232 and Home AutomationNone TDC 11-17-08RS232-HomeAutoTo Bus Sy
Universal RTS Interface II®Back of Interface control boxAntennaIR Sensor InputRS232 Input or RS485 Input RS485 Input/OutputPowerFront of Interface con
Job Name:Location:Dealer:Model:Submittal Date:Drawn:Revised:Revised:As Built:Order #Sheet ___of ___Page 118 of 124Page 120 of 124
Pins may vary per your installationPage 121 of 124
SolarFlex—Sun Tracking Automation® SolarFlex is a sun tracking automation software which takes your buildings fl oor plan and runs the shades accordin
SolarFlex—Sun Tracking Automation—page 2 Below is a picture of what the PC will be showing.www.draperinc.com(765) 987-7999Page 123 of 124
®Region Regional Manager Shade RegionShade Sales Specialist CT, NH, ME, MA, RI, VT, Eastern Canada (NB, NF, NS, PE, ON, QC)Eric Guffey, LEED® AP, CT
OPERATIONA. INITIAL SETUP 1. Connect a 9v DC transformer (included) to the receptacle on the back of the control box. The LED will light green to in
RTS Repeater®DescriptionThe RTS Repeater can be used in installations to extend the range of the standard Radio Technology signal. It will receive the
Radio Motor Accessories® In the previous section radio motor transmitter information was given. This section talks about the accessory parts that com
Battery Wands® Battery Wands are the power source for battery motors. Wands do come with every motor purchased. Replacement wands can be pur-chased i
Plug-In Transformers® These transformers are for supplying 24VDC to our low voltage motors. There are 6 types of transformers, but the numbers and ty
DIN-Rail Transformer—DR-120®Features:- AC input range selectable by switch- Protections: Short circuit/Overload/Over voltage/Over temperature- Cook
DIN-RailTransformer—DR-120—Page 2www.draperinc.com(765) 987-7999Page 19 of 124
Introduction to Motorized Shades Motorized shades can be a big profi table opportunity or a big pain depending on how you go about it. Being educated
DIN-RailTransformer—DR-240®Features:- Universal AC input/full range- Built in active PFC function- Protections: Short circuit/Overload/Over voltag
DIN-RailTransformer—DR-240—Page 2www.draperinc.com(765) 987-7999Page 21 of 124
DIN-RailTransformer—DR-480S®Features:- AC input range selectable by switch- Built in passive PFC function compliance to EN61000-3-2- High-effi cienc
DIN-RailTransformer—DR-480S—Page 2www.draperinc.com(765) 987-7999Page 23 of 124
5 and 10 Motor Power Panels® The 5 & 10 motor power panels are for powering the Low Voltage Radio Motors. They are not required, but they do make
8 Motor Power Panels® The Power Distribution Panel is used to distribute 12 or 24V DC power to up to 8 low voltage motors. The panel includes mounti
RTS Receiver for Standard Motor® The Universal Receiver provides RTS capability to standard motors. It can be used stand-alone as a radio control, or
OPERATING INSTRUCTIONSSystem Set Up① With power off, wire the Universal Receiver as indicated above. Turn all circuit breakers on (motors should not
Sunis™ RTS Light SensorProgramming/Operating/Installation Instructions®DESCRIPTIONThe Sunis RTS Light Sensor is a wireless radio transmitter compatibl
STEP TWO: INSTALLATION MOUNTING SUNIS™ LIGHT SENSOR TO WINDOW GLASS OR SILL ① Attach the “screw-in" suction cup mounting device for Window Mou
Installation TipsMotor Testing It is recommended to test and set all motor limits prior to electrician wiring motor. Draper sells a test cord, C116.0
www.draperinc.com(765) 987-7999Sunis™ RTS Light Sensor Programming/Operating/Installation InstructionsPage 3 of 4STEP FOUR: OPERATION The Sunis Wire
www.draperinc.com(765) 987-7999Sunis™ RTS Light Sensor Programming/Operating/Installation InstructionsPage 4 of 4REPLACING THE BATTERY The Sunis RTS
Toggle Switch (SP/DT) and Princess Rocker (DP/DT)® The maintain toggle switch (SP/DT) is the standard switch which is sent with shades. Maintain swit
®USES: The KS-3 replaces the standard single-station control switch for all products (screens, shades or projector lifts) where the directional func
®USES: The MS-3R and MS-4R are 3- and 4-wire versions of the same switch, used for controlling one screen from multiple locations, using the motor’s
Motor Pigtails and Disconnects®Motor Pigtails are a standard of 6’ with a 18 gauge 3 conductor with a ground on 4 wire motors. It is a 18-2 with 3 wir
Isolating Relays® The isolating relay (ISO relay) prevents feedback between motors and allows multiple motors to run off a 120V switch. The switches
Copyright ©2007 Draper Inc. Form ISO_WD07-R4 Printed in U.S.A.Wiring Instructions ™ Isolating Relay by DraperWiring Diagram of more than o
IntelliFlex™ GC4® The GC4 (group control 4 motors) prevents feedback between motors and allows multiple motors to run off a 120V switch. The switches
Copyright ©2007 Draper Inc. Form GC4_WD07-R Printed in U.S.A.Please Note➀ Make sure power is disconnected before installing controls.➁ This produc
Terms In trying to understand motorized shades, it is important to know certain terminology. These terms used by Draper, electricians, and others whe
IntelliFlex™ SC1® The SCI (smart control 1 motor) gives intelligence to standard motor. This intelligence allows you to group shades and run them fro
Wiring Instructions ™ SC1-Gen2 Control by Draper Copyright ©2009 Draper Inc. Form SC1-Gen2_WD09 Printed in U.S.A.Caution➀ Make sure power
IntelliFlex™ SGC4® The SGC4 (smart group control 4 motors) gives intelligence to standard motors. This intelligence allows you to group shades and ru
Copyright ©2009 Draper Inc. Form SGC4-Gen2_WD09-R Printed in U.S.A.Caution➀ Make sure power is disconnected before installing controls.➁ SGC4 is a
IntelliFlex™ SPGC4® The SPGC4 (smart programmable group control 4 motors) gives intelligence to standard motors. This intelligence allows you to grou
Copyright ©2009 Draper Inc. Form SPGC04-Gen2_WD09 Printed in U.S.A.Caution➀ Make sure power is disconnected before installing controls.➁ SPGC4 is
IntelliFlex™ Inputs® We have many different low voltage input devices for controlling shades through IntelliFlex. Here is a listing and brief descrip
Input Device Sample Confi guration ™ by DraperCopyright ©2007 Draper Inc. Form IntelliFlex-InputDeviceConfi g07 Printed in U.S.A.Notes
Installation Instructions ™ IR Remote Control by DraperCopyright ©2004 Draper Inc. Form IntelliFlex-IR_Inst04 Printed in U.S.
IntelliFlex™ IR Remote Control by Draper Page 2 of 2www.draperinc.com(765) 987-7999The complete table of codes (in hex) is:Installing IR Eye Only into
Radio Motor Transmitters There are several types of radio motor transmitters, and here is a listing of them and when you need them. A radio motor can
Installation Instructions ™ RF Remote Control by DraperCopyright ©2007 Draper Inc. Form IntelliFlex-RF_Inst07 Printed in U.S.A.➀ The Rad
IntelliFlex™ RF Remote Control by Draper Page 2 of 2A Note on InterferenceThis equipment has been tested and found to comply with the limits for a cla
byCopyright © 2007 Draper Inc. Form IntelliFlexWall Switch_Sub07 Printed in U.S.A. ™ Wall SwitchPROJECT:ARCHITECT:CONTRACTOR:SUPPLIER:DAT
Page 2 of 2IntelliFlex Wall Switch by Draperwww.draperinc.com(765) 987-7999Hardwired “Bus” Command SwitchRF “Bus” Command SwitchDry Contact Switch (no
Installation Instructions ™ Wall Switch by DraperCopyright ©2007 Draper Inc. Form IntelliFlex-WallSwitch_Inst07 Printed in U.S.A.If you en
Page 2 of 2IntelliFlex Wall Switch by Draperwww.draperinc.com(765) 987-7999Programming IntelliFlex SwitchDry Contact: Does not have a Bus connection,
Installation Instructions ™ R2D7 RS232 Professional Integration Interface by DraperCopyright ©2004 Draper Inc. Form IntelliFlex-RS232
Installation and Programming Guide Sun and Wind Sensor V1.l and Sun Sensor Switch V4 by Draper, Inc. Connect to the Sun and Wind Sensor as shown: Al
SUN AND WIND SENSOR V1.l and SUN SENSOR SWITCH V4 by Draper Page 2 of 9 The Program Mode LED must now be lit solid GREEN, if it is not, repeat
SUN AND WIND SENSOR V1.l and SUN SENSOR SWITCH V4 by Draper Page 3 of 9 Sun Actions: This Sheet uses "#" for this unit's access
Telis Transmitters Telis hand-held radio transmitters are compatible with RTS Motors and external RTS receivers such as Centralis or HRC-RF. Each Te
SUN AND WIND SENSOR V1.l and SUN SENSOR SWITCH V4 by Draper Page 4 of 9 Defaults: Sun sensor timing = 10 minutes, low sunrise at 68 with incre
SUN AND WIND SENSOR V1.l and SUN SENSOR SWITCH V4 by Draper Page 5 of 9 Three Intermediate Positions on Sun, use default settings (S+7+7 >
SUN AND WIND SENSOR V1.l and SUN SENSOR SWITCH V4 by Draper Page 6 of 9 SUN assuming fixed levels The sun sensor is capable of sending indepen
SUN AND WIND SENSOR V1.l and SUN SENSOR SWITCH V4 by Draper Page 7 of 9 Press an open or close command on the IR transmitter and make sure the
SUN AND WIND SENSOR V1.l and SUN SENSOR SWITCH V4 by Draper Page 8 of 9 NO intermediate positions on Sun: High (2nd from the top) and medium
SUN AND WIND SENSOR V1.l and SUN SENSOR SWITCH V4 by Draper Page 9 of 9 You cannot program the Sun Sensor Switch using S+7+7 CloseALL unless y
Installation Instructions ™ LCD Timer by DraperCopyright ©2007 Draper Inc. Form IntelliFlex-LCDTimer_Inst07 Printed in U.S.A.➀ The time
IntelliFlex™ LCD Timer by Draper Page 2 of 3www.draperinc.com(765) 987-7999Programming/Setting the LCD TimerResetting the timerPress the reset and the
www.draperinc.com(765) 987-7999IntelliFlex™ LCD Timer by Draper Page 3 of 3Page 68 of 124
Installation Instructions ™ PSI60 Bus Command Converter by DraperCopyright ©2007 Draper Inc. Form IntelliFlex-PSI60_Inst07 Printed in U.S.
20-Channel Transmitter This is a 20-channel, Composio, handheld transmitter for Radio Motors. It has an interactive screen for setting functions. It
Introductory Overview The IntelliFlex Control System is an intelligent yet simple package of controls and input devices that provides a single source
byCopyright © 2007 Draper Inc. Form IntelliFlex_PlanningSheet07-R Printed in U.S.A. ® ControlsPlanning SheetPROJECT:ARCHITECT:CONTRAC
SC-1 Quick Reference Guide (OS fi rmware version 3) by DraperThis Sheet uses # for the receiver’s main channel number - new units will use a 1 where #
Page 2 of 2SC-1 Quick Reference Guide by Draperwww.draperinc.com(765) 987-7999Defaults:Main Channel = 1, Group Channels 1-6 = off, no sequencing actio
Intelligent (ILT) Motor Overview® The Intelligent Motor is designed to offer the sophisticated, diverse control of a window shade. The motor contains
ILT Switch and Limit Sets® The ILT switch has a modular connector on the back to plug in the Intelligent Motor, once the motor is connected then limi
ILT Dry Contact InterfaceWiring Diagram® The ILT Dry Contact Interface will operate up to four ILT motors as a group from an external device such as
Draper Digital Network IP Interface® The Draper Digital Network IP Interface is a serial device server used to con-nect the RS485 SDN BUS consisting
Draper Digital Network® The Draper Digital Network which is run from the IP interface mentioned on the previous page is programmed through a series o
The next part of the install is to program the group addresses. For this you will have to check several different things: 1 Are the low voltage li
DECORA RTS SWITCHOperating Instructions The Decora RTS Switch (single or four channel) is a wireless radio transmitter compatible with all the RTS MO
RS485-ILT Link®DESCRIPTION The RS485-ILT Link will enable third party communication to Somfy’s line of intelligent (ILT) motors, and for programming
Draper Digital Network—Smart Switch®Description: The Smart Switch is a control device whichoutputs the DDN protocol over RS-485, providing digitalcont
Draper Digital Network (DDN)—Sample Confi guration®12312V DC Power SupplyPart No. C215.018To LAN6-ButtonSmart DDN SwitchPart No. C112.111Draper Digital
Motor End Cap Small C002.571 Large C002.677
® Standard motor Motor Specifi cations Available tube sizes Draper Products Min/ at a glance Max, C.O., Limit TypeQuiet MotorTorque (Nm)R
Motor Name: 506S2RH RPM: 38 Volts: 120 Amps: .95 Min. Shade Width: 24” om With Crank Override 29” om Standard Motor Lead Length: 6’ Lea
Motor Name: 510S2RH RPM: 38 Volts: 120 Amps: 1.3 Min. Shade Width: 25” om With Crank override 30” om Standard Motor Lead Length: 6’ Lead
Motor Name: 504S2RH-ST RPM: 32 Volts: 120 Amps: .95 Min. Shade Width: 32” om With Crank Override 37” om Standard Motor Lead Length: 6’ L
Motor Name: 506G RPM: 34 Volts: 120V Amps: .9 Min. Shade Width: 24” om Standard Motor Lead Length: 6’ Lead Type:
Motor Name: 506S2ILTRH RPM: 38 Volts: 120 Amps: .95 Min. Shade Width: 27 1/4” om With Crank Override 32 1/4” Standard Motor Lead Length:
www.draperinc.com(765) 987-7999DECORA RTS SWITCHMounting Instructions The special low-voltage bracket is specifi cally designed to mount the Decora RT
Motor Name: 504S2ILTRH-ST RPM: 38 Volts: 120 Amps: .95 Min. Shade Width: 32” om Standard Motor Lead Length: 6’ Lead Type:
Motor Name: 506S2RH-RTS RPM: 38 Volts: 120 Amps: .95 Min. Shade Width: 27 1/8” om With Crank Override 32 1/4” Standard Motor Lead Length:
Motor Name: 510S2RH-RTS RPM: 38 Volts: 120 Amps: 1.3 Min. Shade Width: 29” om With Crank override 34” om Standard Motor Lead Length: 6’
Motor Name: 504S2RHST-RTS RPM: 38 Volts: 120 Amps: .95 Min. Shade Width: 32” om Standard Motor Lead Length: 6’ Lead Type:
Motor Name: 506S2PA RPM: 38 Volts: 120 Amps: .95 Min. Shade Width: 36” om Standard Motor Lead Length: 6’ Lead Type:
Motor Name: 510S2PA RPM: 38 Volts: 120 Amps: 1.3 Min. Shade Width: 36” om Standard Motor Lead Length: 6’ Lead Type:
Motor Name: 506S2ILT RPM: 38 Volts: 120 Amps: .95 Min. Shade Width: 36” om Standard Motor Lead Length: 6’ Lead Type:
Motor Name: 506S2-RTS RPM: 38 Volts: 120 Amps: .95 Min. Shade Width: 36” om Standard Motor Lead Length: 6’ Lead Type:
Motor Name: 510S2-RTS RPM: 38 Volts: 120 Amps: 1.3 Min. Shade Width: 36” om Standard Motor Lead Length: 6’ Lead Type:
Motor Name: 506S1RH RPM: 38 Volts: 230 Amps: .95 Min. Shade Width: 24” om With Crank Override 29” om Standard Motor Lead Length: 6’ Lea
Kommentare zu diesen Handbüchern