Installation Instructions
Fascia for Battery and 24 Volt Dual Roller FlexShade by Draper
Copyright © 2014 Draper Inc. Form Fascia_Battery_24V_DualRoller_Inst14 Printed in U.S.A.
Continued
If you encounter any difficulties installing or servicing your Fascia
for Dual Roller FlexShade System, call your dealer or Draper, Inc.,
Spiceland, Ind., (765) 987-7999 or fax (765) 987-7142.
Caution
1 Inspect all boxes to make sure you have received the proper shades and
parts. Controls may be shipped separately, or in same carton as shades.
2 Open cartons lengthwise.
3 Before connecting switches, controls, or electrical, make sure power is off.
Wiring indicated in diagram by dashed lines must be completed by an
electrician.
4 Do not wire motors in parallel without written permission from Draper.
5 It is the installer’s responsibility to make sure appropriate fasteners are
used for mounting surface.
6 All endcaps, fascia, and other hardware must be installed level. Shades
must be level and square.
7 Please read the following installation guidelines thoroughly and
follow them carefully. Failure to do so may cause product to fall or
otherwise fail, and invalidates warranty.
Mounting Endcaps
1 Snap endcap covers onto endcaps. The proper orientation of Left-Hand,
Right-Hand, Front and Back is molded into endcap covers (see Fig. 1).
2 Mark wall, jamb or ceiling for placement of mounting endcaps.
Caution: Before mounting shades, verify measurements on the card
provided with the shade, and ensure the endcaps are installed at the
correct width.
3 Drill small starter hole (if necessary) in mounting surface.
4 Mount endcaps using appropriate fasteners for surface.
LEFT-HAND TOP
RIGHT-HAND TOP
LEFT-HAND TOP
RIGHT-HAND TOP
BEAD CHAIN CLUTCH,
24V AND BATTERY
OPERATOR ENDCAPS
ENDCAP
COVER
SNAP-ON
SNAP-ON
ENDCAP
COVER
SNAP-ON
Figure
NOTE:
It is essential that endcaps are fastened securely
to the mounting surface and are not able to move
from side to side.
For Battery-Powered Motors:
5 Mount battery wands to wall using provided mounting clips (see Fig. 2).
Be sure to locate the battery wands where they can reach the motor with-
out interfering with shade/roller operation.
Please Note: If mounting the battery wands vertically, small plastic grips are
provided to slide onto the battery pack and create a snugger fit in the bracket.
6 Place rear shade spring-loaded
pin in idler endcap, depress
spring-loaded pin by pressing the
shade roller toward the endcap
and slip operator end of rear
shade into slots on operator end
endcap (see Fig. 3).
7 Connect battery packs together,
and to motor.
8 Repeat with front shade.
For 24V Motors:
5 Place rear shade spring-loaded pin in idler endcap.
6 Depress spring-loaded pin by pressing the shade roller toward the endcap.
7 Slip operator end of rear shade into slots on operator end endcap (refer-
ence Fig. 3).
8 Repeat with front shade.
Installing Fascia
9 Place groove along top of fascia over end caps, and snap into place (Fig.4).
Fascia is not fully seated until it clicks into place on both ends.
Once in place, check for secure fit. If not secure, secure with
appropriate fastener (not included).
Figure
Figure
STEP 2
Clicks into place
STEP 1
Figure
NOTE:
The installer is responsible for selecting appropriate
mounting hardware for site conditions.
(4 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern