Draper Cineperm Installationshandbuch PDF herunterladen

Installation Instructions

Cineperm Permanently Tensioned Projection Screen by Draper

Frame Assembly

Standard Frame—

① Lay out frame pieces on ﬂ oor, by matching up color-coded tape near

corners. Snaps should be facing up.

② Assemble frame (see Fig. 1). If nec es sary gently tap frame ends with a

rubber mallet to make sure castings are fully seated.

Surface Installation

① Carefully remove surface from cardboard tube and unroll onto a clean

cloth or paper.

② Engage snaps in each corner, then secure rest of screen snaps.

③ Stretch fabric across frame. Use extreme caution when attaching fabric.

Overstretching or rough handling could cause the viewing surface to tear.

Frame Installation (Standard Frame)

Outside (Face) Mount—

① Drill mounting holes in frame (see Fig. 2).

② Mark wall and drill holes to correspond with those in the frame.

③ Enlarge holes in frame side furthest from wall to allow screw heads to pass

through (see Fig. 2). Do not allow screw heads to remain outside the

frame: overtightening could bend frame and affect screen ﬂ atness.

Cineperm

frame

Mounting hardware

by others

Viewing surface snaps to

frame, covering mounting holes

Supporting structure

Drill through frame for

mounting hardware.

Enlarge first hole for screw

head to pass through.

Figure 2

Figure 3

Inside (Jamb) Mount—

① Place frame assembly in opening to check for a snug ﬁ t. If frame is too

large, opening may have to be enlarged. If frame is too small or does not

sit square in the opening, shims and caulking may be required.

② Drill mounting holes in frame, and enlarge the ﬁ rst holes to allow screw

heads to pass through (see Fig. 3). Do not allow screw heads to remain

outside the frame: overtightening could bend frame and affect screen

ﬂ atness.

③ Drill holes in jamb.

④ Attach frame using appropriate fasteners for mounting surface (provided

by others).

⑤ Use caulk to ensure there is no light leakage around edges of frame.

Truss Frame—

① Unfold and lay out pieces on ﬂ oor, by matching up color coded marks.

Lock all hinges (see Fig. 1). Stage Left and Stage Right sections should be

placed with snaps up. Top and bottom sections should be placed with

snaps down.

② To increase frame rigidity, hinges on top and bottom sections have rivnuts

marked with red and green. Insert a Handy Crank through the threadless

rivnut (red) and tighten into the threaded rivnut (green).

③ Apply small sections marked “Stiffener Bars” to back of bottom frame

section, using 8 Handy Cranks. These eliminate sag on large suspended

frames. Failure to use all Handy Cranks may result in screen frame

damage. Turn bottom frame section over so snaps face up.

④ Repeat step 3 for top frame section.

⑤ Join top and bottom sections to Stage Left and Stage Right, using 2

Handy Cranks on each of the 4 corners. Match numbers on white labels.

NOTE: No Handy Crank should protrude outside screen frame.

⑥ Attach surface (see “Surface Installation”), and suspend using appropriate

materials (provided by others to meet speciﬁ c installation requirements).

Opening

Wall

Anchor bolt by others.

Clearance hole in outer

wall by others.

Snap-on viewing surface

1" square

alum. tube

Wall

Anchor bolt by others.

Clearance wall in outer

wall by others.

Locate between snaps.

1 square

alum. tube

Snap-on viewing surface

Inside (Jamb) Mount

Outside (Face) Mount

④ Attach frame to wall using appropriate fasteners for mounting surface

(provided by others).

NOTE: Measure screen frame width at the top, bottom, and center; Make

sure the frame is installed so the center width is same as the width at

the top and bottom.

Figure 1

Standard Frame

Truss Style Frame

Caution

① Read instructions through completely before pro ceed ing.

② Follow instructions carefully. Installation con trary to instructions

invalidates warranty.

③ Bent or warped frames will affect surface ﬂ atness and image quality.

④ Screen should be square, and width should not vary from the center to

the ends of the frame

⑤ When lifting assembled screen, do not lift at only one corner; lift at both

corners. Lifting by one corner could result in damage to the screen

frame, especially on large screens.

⑥ Screen should be installed level (using a carpenter’s level).

⑦ Nothing should be fastened to screen frame or viewing surface.

⑧ Be careful not to rip screen material when attaching surface to frame.

⑨ The ideal temperature range for assembling this screen to prevent

damaging the surface is 68°-78° F (20°-26° C). Assembling below

recommended temperatures may damage surface and void warranty.

NOTE: Screen has been inspected and tested at factory prior to shipment.

Jamb of opening

Viewing Surface snaps to

frame, covering mounting holes

Cineperm

frame

Drill through frame for

mounting hardware. Enlarge

first hole for screw head

to pass through.

Mounting hardware

by others

Color-coded

tape

Handy

Cranks

If you encounter any difﬁ culties installing or servicing your Cineperm, call your

dealer or Draper, Inc. in Spiceland, In di ana, 765-987-7999, or fax 765-987-7142.

Always fold viewing surface with snaps face-to-face.

Do not permit screen fabric to contact border material

or snaps when folded. Store in pouch provided.

Installation Instructions 1

Inhaltsverzeichnis

Seite 1 - Installation Instructions

Kommentare zu diesen Handbüchern

Keine Kommentare

Draper Cineperm Installationshandbuch

Stöbern Sie online oder laden Sie Installationshandbuch nach Projektionswände Draper Cineperm herunter. Draper Cineperm Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Projektionswände Draper Cineperm