Draper SLX12 Betriebsanleitung PDF herunterladen (Seite 4)

230V AC Scissor Lift SLX by Draper page 4 of 7

(765) 987-7999www.draperinc.com

KEY

WALL

RP/RQ

LVT

RP/RQ Bus Ports for

remote controls such as

IR Eye, RF Receiver, LED

Wall Switch and RS232

Low Voltage Tr igger

(6-24 VDC)

(No +/- wiring requirement)

Function Indicator

DCU

Green

Black

Yellow

LVC-S

1 2 3 4 5 6

Y G R B

Red - Down

Black - Com

Blue - Up

Green

Yellow

Black

SP-KSM

1 2 3 4 5 6

Y G R B

To RS232 Port:

Yellow = Rx (Data from control system)

Green = Tx (Data to control system)

Red = Unused

Black = Gnd (Signal Ground)

1 2 3 4 5 6

Y G R B

6 5 4 3 2 1

B R G Y

DETAIL OF DATA CABLE

SPLITTER BOARD

Low voltage

wiring by others

R2D7 (Optional)

Please Note:

Data cable connections must be made using

electrically straight 4-conductor modular cable

(RJ14). If making your own cables, this means

colors do not cross over: blue leads to blue, green

to green, etc. (see diagram below).

1 2 3 4 5 6

Y G R B

1 2 3 4 5

Y G R B

Connecting Controls to Data Cable Splitter Board

Controls plug into the Data Cable Splitter Board, which is located on

the Top Frame on the front side of the lift, using RJ14 connectors.

For IR or RF Remote Control, use data cable with RJ14 connectors

on both ends.

For serial control of "Show" position, use data cable with RJ14

connectors on both ends and an R2D7 Serial Control Interface.

Plug into the "RP/RQ" input.

Any control, including automated dry contact systems, being

connected to the wall switch input MUST send a momentary signal.

Optional Delay Feature

1 When the Optional Delay Feature is installed the Delay Switch must be in

the "Delay On" position for normal operation.

2 If the Optional Delay Feature is installed and the "Show Position" requires

adjusting, then the "Delay Switch" must be switched to OFF while adjusting

the show position.

CAUTION: Be sure all switches are in OFF position before adjusting limit

switch. Always be prepared to shut lift off manually when new adjustment is

being tested. Please refer to wiring diagram.

PLEASE NOTE: If the Scissor Lift loses power, the DOWN

function will not work until you operate the lift in the UP

direction using the wall switch. This allows the lift's control

encoder to recognize it's "home" location.

CLEARING THE SHOW POSITION AT CURRENT SHOW POSITION:

1 Move lift to the show position.

2 While lift is at the show position press and hold the Key Up toggle

switch and release once the Lift begins moving upward.

3 The show position is now cleared and ready for a new show position

to be set.

CLEARING THE SHOW POSITION AT THE MAINTENANCE POSITION:

1 Move lift to the maintenance position.

2 While lift is at the maintenance position press and hold the Key Down

toggle switch and release once the Lift begins moving upward.

3 The show position is now cleared and ready for a new show position

to be set.

PROCEDURE FOR SETTING SHOW POSITION:

1 Now that the show position has been cleared, use wall switch up and down

buttons to get lift into desired show position.

2 While lift is at desired show position, press and hold the Key Down toggle

switch until lift begins to move upward. Lift will begin a calibration cycle

where it will move upward for two seconds, stop then move down for one

second and then the Lift will return to the desired show position.

PLEASE NOTE: At this point the Key Switch will not operate until

the new “Show Position” has been set. Also the 3-Button Wall Switch

changes into a maintain, push and hold type button, for continuous

movement. This allows for easy setting of new “Show Position”)

Adjusting Limit Switches

PLEASE NOTE:

Changing the fully open or fully closed position will reset the

electronic controls and cuase the lift to operate improperly.

Please call Draper before attempting these adjustments.

1 2 3 4 5 6 7

Kommentare zu diesen Handbüchern

Keine Kommentare

Draper SLX12 Betriebsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Projektorhalterungen Draper SLX12