Draper Access/Series M AutoReturn Betriebsanleitung PDF herunterladen

Installation/Operating Instructions

Access/Series M Projection Screen by Draper

Caution

➀ Read instructions through completely before proceeding.

➁ Follow instructions carefully. Installation contrary to instructions

invalidates warranty.

➂ Entire bottom of screen case should be unobstructed to permit access

to bottom panel for servicing.

➃ Screen should be installed level (using a carpenter’s level).

➄ Nothing should be fastened to screen dowel or viewing surface.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

Hanging Screen

When locating viewing surface and checking clear ance for screen operation,

remember surface is centered in the length of the case. Regardless of

mounting method used, the following points apply:

➀ Mounting brackets are shipped attached to the case. Engage each bracket

with top of housing as shown below and tighten set screws. A bracket

should be within 18" of each end of screen case. Brack ets can be removed

and case mounted with lag screws through top of case (holes drilled on

site).

➁ Screen should be positively and securely supported so that vibration or

even abusive pulling on viewing surface will not weaken installation.

➂ Installer must insure that fasteners used are of adequate strength and

suitable for the mounting surface chosen. Supporting hardware (chains,

cables,

" rods, etc.) must be essentially vertical.

➃ Entire bottom of case must be readily accessible after in stal la tion is

complete.

➄ Front, back and top of case must be straight—not forced to warp or bow.

➅ If case is painted on location, removal of roller/fabric assembly is

recommended prior to painting. If not removed, slot on bottom of case

should be shield ed to protect view ing surface from paint splatters or

overspray.

Bottom Access Panel Installation/Removal

Bottom access panel hooks over the lower inside edge of the screen housing

and then is pivoted downward until the engagement brackets on each end of

the bottom panel click into place with the ball detents on each endcap. Make

sure bottom access panel clicks in place at each end of its length.

With bottom access panel

angled up approx. 20 degrees,

engage hook on the panel

with lip of the housing

Using the hook and lip as a pivot,

pull the panel downward until the

engagement brackets click into

place with the ball detent

on each endcap

Engagement bracket

(one on each end of the

bottom access panel)

Remove bottom access panel by pushing up at each corner of panel adjacent

to slot in bottom of the housing.

With bottom access panel angled up approximately at 20° it can be lifted off of

the lip of the housing and then lowered out of the housing completely.

Bottom flange of Access housing

Bottom access panel pushup

points for panel removal

Caution: Beware of pinch

points at ends of closure

Access case as seen from below

Spring Roller/Fabric Installation

The bottom access panel must be removed ﬁ rst.

The spear end mounting bracket has rectangular openings for accepting roller

spear. Back out the four set screws in bracket until they are ﬂ ush with top side

of bracket.

To engage the spear end bracket ﬂ ange above the two channels in the top of

the screen housing, rotate the bracket approximately 45° counterclockwise

to allow the top surface of the motor bracket to rest ﬂ at against the top

inside of the housing. Rotating the bracket clockwise until it is engaged with

the channels, slide it along the length of the housing toward the left end of

housing, leaving approximately

" clearance between bracket and endcap.

Tighten the four set screws on the bracket ﬂ ange using

" hex key.

Engage the idler end bracket (nylon bushing) in the same manner as the

spear end bracket and slide it toward the opposite end of the screen housing.

Do not tighten the set screws on this bracket until the roller/fabric assembly is

installed.

Locate the roller/fabric assembly and remove the retaining clip and ﬂ at washer

from the idler end pin, and remove retaining clip from the spear. Remove

brackets from roller.

NOTE: This may require two people to perform safely. Raise the roller/

fabric assembly up into the screen housing and engage the spear of the roller

completely into the spear mounting bracket.

If roller is 1

" diameter, there will be an arrow imprinted on the spring end

of the roller. This arrow must be pointing UP, and you must use the slot

closest to the edge of the bracket.

If roller is 2

" or 3" diameter, there will be a notch cut out on the spring

end of the roller. This notch must be pointing DOWN, and you must use the

appropriate slot.

(Continued on page 2)

If you encounter any difﬁ culties installing or servicing your Access/Series M screen, call

your dealer or Draper, Inc., in Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.

Typical

Installation

Alternate

Installation

(additional

set of

brackets

required

but not

included)

Slots along

top of case

permit

brackets to

be set at an

angle

1 2

Inhaltsverzeichnis

Seite 1 - Caution: Beware of pinch

Installation/Operating InstructionsAccess/Series M Projection Screen by DraperCaution➀ Read instructions through completely before proceeding.➁ Follow

Seite 2 - Case Dimensions

Access/Series M by DraperPage 2 of 2(Continued from Page 1)Install the retaining clip on the spear, locking spear and bracket together.While supportin

Kommentare zu diesen Handbüchern

Keine Kommentare

Draper Access/Series M AutoReturn Betriebsanleitung

Stöbern Sie online oder laden Sie Betriebsanleitung nach Projektionswände Draper Access/Series M AutoReturn herunter. Draper Access/Series M AutoReturn Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Projektionswände Draper Access/Series M AutoReturn