Draper SC1 Bedienerhandbuch PDF herunterladen (Seite 107)

Installation Instructions

Motorized FlexShade by Draper

Mounting Brackets

➀ Mark wall, jamb or ceiling for placement of mounting brackets.

Caution: Before mounting shades, verify measurements on the card

provided with the shade, and ensure the brackets are installed at the

correct width.

➁ Drill small starter hole in mounting surface (if necessary).

➂ Mount brackets using appropriate fasteners for surface (see Fig. 1 for

bracket types). The installer is responsible for selecting mounting

hardware appropriate for site conditions.

Ceiling

Inside/Outside

Idler End

(Left Standard)

Operator End

(Right Standard)

Brackets

Figure 2

Endcaps

Idler End

(Left Standard)

Operator End

(Right Standard)

Figure 5

Caution

➀ Inspect all boxes to make sure you have received the proper shades and

parts. Controls may be shipped separately, or in same carton as shades.

➁ Open cartons lengthwise.

➂ All brackets, fascia, headboxes, pockets, wall clips, and other hardware

must be installed level. Shades must be level and square.

➃ All motors should be tested and limits set using test cord before electrician

wires shade.

➄ Before connecting switches, controls, or electrical, make sure power is off.

Wiring indicated in diagram by dashed lines must be completed by an

electrician.

➅ Do not wire motors in parallel without written permission from Draper.

➆ It is the installer’s responsibility to make sure appropriate fasteners are

used for mounting surface.

➇ Please read the following installation guidelines thoroughly and follow

them carefully. Failure to do so may cause product to fall or otherwise

fail, and invalidates warranty.

Please Note: Custom products/installations may not be reﬂ ected by this

document. Call Draper, Inc. if you have questions about your installation.

Ceiling

Inside/Outside

If you encounter any difﬁ culties installing or servicing your Motorized FlexShade, call

your dealer or Draper, Inc., Spiceland, Ind., (765) 987-7999, or fax (765) 987-7142.

Figure 1

Retainer clip

➃ Place operator (motor) end onto its bracket. If a coupled unit, place slotted

end of shade into coupler bracket, then insert idler pin end of next shade

into coupler bracket.

➄ Slide notched pin on idler end into slot on bracket. Slip retainer clip onto

idler end between bracket and roller (see Fig. 2).

Coupler

(Bearing Boss toward

slotted coupler end)

Shade

Roller

Coupling

(slotted end)

Bearing boss

oriented toward

slotted coupling

Coupling

(idler pin)

Shade

Roller

Mounting Endcaps

➀ Snap end covers into place (see Fig. 3).

➁ Mark wall, jamb or ceiling for placement of mounting endcaps.

➂ Drill small starter hole (if necessary) in mounting surface.

➃ Mount endcaps using appropriate fasteners for surface (see Fig. 4 for

endcap dimensions). If this is a coupled unit, be sure to mount coupled

endcap in the center position. The installer is responsible for selecting

mounting hardware appropriate for site conditions.

Caution: Before mounting shades, verify measurements on the card

provided with the shade, and ensure the endcaps are installed at the

correct width.

➄ Place operator (motor) end into its endcap (see Fig. 5).

➅ For coupled units insert idler pin into center (coupled) endcap. Next Insert

slotted end of next shade into the center (coupled) endcap (see Fig. 5).

➆ Slide notched pin into idler endcap and attach retainer clip(see Fig. 5).

Figure 4

/2"

/8"

/2"

/8"

/4"

/8"

/4"

/16"

/4"

/2"

/4"

/8"

Large Endcap Small Endcap

Retainer clip

Shade

Roller

Coupling

(slotted)

Bearing boss oriented

toward slotted coupling

Bearing

Endcaps

Coupling

(idler pin)

Shade

Roller

Operator

End

Three washers not required

if fascia or headbox endcaps

look like this.

Three washers

required if fascia

or headbox

endcaps look

like this.

Coupler

Figure 3

Fascia

➀ Snap end covers onto endcaps.

➁ If Crank override is provided, remove crank

handle assembly from endcap and discard

washers (see Fig. 6)

➂ Follow steps 1 through 6 under "Mounting

Endcaps" section.

➃ Place groove along top of fascia over end-

caps, and snap into place (see Fig. 7 on

page 2). Fascia is not fully seated until it clicks into place on both

ends. Once in place, check for secure ﬁ t. If not secure, secure with

appropriate fastener (not included).

Please Note: Install motor so that limit switches are accessible.

Figure 6

Retainer

Clips

Operator End

(Small Pocket only)

*Don't forget to

install retainer

clip!

*Don't forget

to install re-

tainer clip!

Page 107 of 120

1 2 ... 102 103 104 105 106 107 108 109 110 111 112 ... 119 120

Kommentare zu diesen Handbüchern

Keine Kommentare

Draper SC1 Bedienerhandbuch Seite 107

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Draper SC1