Draper SC1 Bedienerhandbuch PDF herunterladen (Seite 40)

Please Note

➀ Make sure power is disconnected before installing controls.

➁ SC1 has a rated switching capacity of 6 amps.

➂ SC1 is a line voltage control, designed to operate one motor. Activation

by Low Voltage input commands. If you want to switch two or more

motors, ISO relays must be installed in the circuit.

➃ SC1 is electrically “hot” on the back of the circuit board. INS-SC1 (Draper

Part Number C199.004) insulation board is provided.

Electrical Speciﬁ cations

Input:

Data: +5v AC BUS Commands

Low Voltage: Dry Contact—0v AC

Line Voltage: 115 V AC +/- 10%

Output: 115V AC 6 FLA per SC1

Wiring Instructions

™

SC1 Control by Draper

If you encounter any difﬁ culties installing/wiring your IntelliFlex control, call your

dealer or Draper, Inc., Spiceland, Ind., (765) 987-7999; or fax (765) 987-7142.

Part Number C156.065

Dimensions: 2

/8" W x 3

/4" L x

/8" H.

One SC1 ﬁ ts in a deep single gang J-Box.

Please Note: When connecting data "BUS," never link an "Eye" port to an-

other "Eye" port. You may link your BUS from "Eye" to "Aux" or "Aux" to "Aux."

All BUS command input devices must connect to an "Eye" port in order to

power the input device.

Wiring Instructions for Controlling Multiple Shades with One SC1

Wiring Instructions for Controlling One Shade with One SC1

Inserting wire into spring terminal

➀ Open spring terminal by inserting screw-

driver into upper opening.

➁ Insert wire into lower opening.

➂ Remove screwdriver.

Data BUS

"Eye" Port

Data BUS

"Aux" Port

Dry input terminals.

This can be any Single

Pole, Double Throw switch

IntelliFlex

Motor Neutral

Black - Up

Red - Down

110-120V AC

Motor

115V AC

Hot

Neutral

Ground

NOT

USE

110-120V AC

Motor 1

Green

INPUT

110-120V AC

Motor 2

Green

Neutral

Down

Note:

Motor red and black

wires will need to

"flip" if one motor

is right hand and the

other is left hand.

Data BUS

"Eye" Port

Data BUS

"Aux" Port

Dry input terminals.

This can be any Single

Pole, Double Throw switch

IntelliFlex

Motor Neutral

Black - Up

Red - Down

115V AC

Hot

Neutral

additional

ISOs

Earth

Ground

Neutral

Down

Additional

Motor

Green Wire

SC1

ISO

Note - This wire

is optional if the

ground terminal

is not used

Fabric un roll ing from back of

roller (standard)

Fabric unrolling from front of

roller (reverse roll)

Interior

side

Interior

side

Right hand motor

(Standard)

Black—Up

Red—Down

Left hand motor

Black—Down

Red—Up

Right hand motor

(Standard)

Red—Up

Black—Down

Left hand motor

Red—Down

Black—Up

All connection wires must conform to the motor manufacturer’s

recommendation and prevailing electrical codes. The switch and control

system wires should be at least 24 AWG and no larger than 18 AWG.

Please Note:

All input devices (low voltage LED switches, IR eye, RF receiver) which

connect to the Eye jack must be connected using electrically straight 4-

conductor modular cable (RJ11). This means colors do not cross over: blue

leads to blue, orange to orange, etc. (see diagram below)

If you use standard telephone cable, you must ﬁ rst remove one connector,

turn it over and re-attach, to ensure that the cable is electrically straight (see

diagram below). Standard phone cable is 26 AWG.

Yellow

Red

Green

Black

Yellow

Red

Green

Black

Yellow

Green

Red

Black

Yellow

Green

Red

Black

Standard Telephone Cable

(Before, will not work)

Telephone Cable After

(Electrically Straight-will work)

Yellow

Green

Red

Black

Yellow

Green

Red

Black

Electrically Straight Data Cable

Using Telephone Cable

Note: Motor red and

black wires will need

to “ﬂ ip” if one motor

is right hand and the

other is left hand.

Please Note: This conﬁ guration

will limit SC1 functions.

Page 40 of 120

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 119 120

Kommentare zu diesen Handbüchern

Keine Kommentare

Draper SC1 Bedienerhandbuch Seite 40

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Draper SC1