Draper SC1 Bedienerhandbuch PDF herunterladen (Seite 110)

Push-Button Limit Switches:

➀ Fully depress both limit switch push buttons, then operate

wall switch to make sure system works properly.

➁ Raise shade to desired “up” stop position.

➂ Set upper limit by depressing and releasing the proper

(back) push button (See Fig. 7).

➃ Lower shade to desired “down” stop position.

➄ Set lower limit by depressing and releasing the proper

(front) push button (see Fig. 7).

NOTE: Each shade’s lim its must be set if using group control.

Adjustments

Figure 7

NOTE: Wiring diagram for standard right-hand motor placement with fabric

from rear of roller, or left-hand motor place ment with fabric from front of roller.

For left hand motor place ment with fabric from rear of roller or right hand mo-

tor place ment with fabric from front of roller, Red is “Up” and Black is “Down.”

Single Shade Wiring Diagram

For multiple shades or low voltage wiring consult diagrams provided with

control.

Electrical Connections

Shade operates on 110-120v, 60 Hz. current. Shade is shipped with internal

wiring complete and control switch (es) fully boxed, and standardly supplied

with a 6' cable lead. Longer lead can be substituted by removing two screws

in motor end of roller, removing lead, plugging new lead in, and replacing

screws. Wire to connect shade to switch (es) and switch (es) to power supply

should be fur nished by installer. Con nec tions should be made in ac cor dance

with attached wiring diagram, and wiring should comply with national and

local electrical codes. DO NOT wire motors in parallel.

All operating switches should be “off” before power is connected.

Internal Shade Wiring

White (Common)

Black (Up)

Red (Down)

Green (Ground)

Control

switch

Single gang box by others

Min. 4" x 2

/8" x 1

/8" deep

Brown

Black

Red

To 110-120V Line

Dashed wiring by electrician

www.draperinc.com

(765) 987-7999

Your shade motor will feature either push-button or setscrew limit switches.

Use appropriate steps below for your type of motor. At no time should viewing

surface be unrolled enough to expose any part of shade roller.

These instructions are for right-hand motor, fabric from rear of roller.

For left-hand motor, fabric from rear of roller, directions noted below

should be reversed.

Setscrew/Socket Limit Switches:

Adjusting Back (White) Socket—White socket is located on the motor end

of roller (see Fig. 8) and is accessible to a small ﬂ at screw driv er

" hex key. Turning the socket counterclockwise will allow

the roller to run farther up or down (as appropriate). Turning it

clockwise will shorten op er a tion, caus ing it to stop sooner. A

full revolution of the socket will alter the stopping position of the

shade by ap prox i mate ly 1

Adjusting Front (Yellow) Socket—Yellow socket is located on

the motor end of roller (see Fig. 8) and is accessible to a small

ﬂ at screwdriver. Turning the socket counterclockwise will allow

the roller to run farther up or down (as appropriate). Turning it

clockwise will shorten op er a tion, caus ing it to stop sooner. A full revolution of

the socket will alter the stopping position of the shade by ap prox i mate ly 1

Please Note: Each shade’s lim its must be set if using group control.

FlexShade 2 Instructions by Draper page 2 of 2

Fascia

➀

Mount endcaps and follow steps outlined in "Shade Installation" section to

assemble shade.

➁

Run electrical wiring (see "Electrical Connections").

➂

Set limits (see "Adjustments").

➃

Install fascia (see Fig. 6).

Figure 6

Back

(White)

Front

(Yellow)

Bottom View

Side View

Figure 8

Screws

Front

(Yellow)

Back

(White)

Bottom View

Side View

Shade Width

Fascia or Headbox Fabric Width = Shade Width - 2"

Brackets Only Fabric Width = Shade Width - 1

/8"

Headbox/Fascia

with Endcaps

Brackets Only

Dimensions

Headbox Fascia Brackets

with Endcaps with Endcaps Only

A 6

" 6

" 5

B 6

" 6

" 5

C N/A N/A 3

D N/A N/A 3

E 1" 1"

Please Note: Maximum bundle diameter is 5

/4" (for

Headbox, Fascia or Brackets)

Centers of mounting holes in endcaps and brackets are located approxi-

mately

" in from the outer edge of the endcap/bracket.

Cleaning and Maintenance

Idlers on motorized shades may occasionally need lubrication. If lubrica-

tion is required, apply a small amount of a lithium based grease direct to the

idler pin.

Most of Draper’s standard fabrics may be cleaned at the window by

vacuuming with a soft brush attachment. They may also be cleaned by using

a sponge or soft cloth and mild solution of warm soapy water. A dishwashing

liquid, such as Ivory liquid, is recommended. A clean dry cloth is recommend-

ed for the metal ﬁ nish. Exceptions are Flocké and Roc-Rol fabrics, which

must be cleaned with a dry art sponge.

Page 110 of 120

1 2 ... 105 106 107 108 109 110 111 112 113 114 115 ... 119 120

Kommentare zu diesen Handbüchern

Keine Kommentare

Draper SC1 Bedienerhandbuch Seite 110

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Draper SC1