Draper SC1 Bedienerhandbuch PDF herunterladen (Seite 109)

Installation Instructions

FlexShade 2 by Draper

Mounting Brackets and Endcaps

➀

Mark wall, jamb or ceiling for placement of mounting brackets or endcaps.

➁

Drill small starter hole in mounting surface (if necessary).

➂

Mount brackets using appropriate fasteners for surface (see Fig. 1 for

bracket and endcap types). Centers of mounting holes are approximately

" in from outer edge of endcap/bracket.

Please Note: It is the responsibility of the installer to ensure the mounting

surface and mounting hardware are of appropriate type and strength.

Shade Installation

Pin End (Left Standard) Motor End (Right Standard)

Mounting Brackets

Figure 3

Endcaps for Headbox or Fascia

Figure 1

Caution

➀ Inspect all boxes to make sure you have received the proper shades and

parts. Controls may be shipped separately, or in same carton as shades.

➁ Open cartons lengthwise.

➂ All brackets, fascia, headboxes, pockets, wall clips and other hardware

must be installed level. Shades must be level and square.

➃ Before connecting switches, controls, or electrical, make sure power is off.

Wiring indicated in diagram by dashed lines must be completed by an

electrician. Do not wire motors in parallel.

➄ Installation of this product requires two people.

➅ It is the installer’s responsibility to make sure appropriate fasteners are

used for mounting surface.

➆ Please follow installation guidelines carefully. Failure to do so invalidates

warranty.

If you encounter any difﬁ culties installing or servicing your FlexShade 2, call your

dealer or Draper, Inc., Spiceland, Ind., (765) 987-7999, or fax (765) 987-7142.

Pin End (Left Standard) Motor End (Right Standard)

Please Note: Installation of Shade Assembly requires two people.

➀

Remove screw from the motor retainer ring.

➁

Install the motor retainer ring into the groove in the motor end bracket (see

Fig. 2). Do not re-install the screw yet.

➂

Rotate the roller assembly idler pin so that the ¼" hole in the shaft is

aligned with the ¼" hole in the idler end bracket (see Fig. 3).

➃

Place idler pin into the idler end bracket.

➄

Insert the cotter pin through the idler end bracket and shaft.

➅

Insert the motor end of the roller assembly into the motor end bracket (see

Fig. 3).

Figure 2

Caution: The cotter pin must be correctly installed to insure safe operation of

the shade. If misalignment of the holes in the idler shaft and bracket prevent

the cotter pin from being installed, then the roller assembly must be com-

pletely removed and re-installed.

➆

Ensure that the motor retainer ring is properly installed around the grooves

in the motor and the motor end bracket.

➇

Install the motor retainer ring screw and tighten.

Please note: Maximum torque for tightening screw is 5 lb-inches.

➈

Use the cable strap with self-adhesive attachment pads to secure the mo-

tor cable to the endcap (see Fig. 4). This will prevent possible damage to

the cable by the roller during shade operation.

Cotter Pin

Headbox

➀

Remove headbox cover (see Fig. 5).

➁

Remove shade and roller from headbox/endcaps.

➂

Mount headbox and endcaps in desired location.

➃

Re-install shade roller (see "Shade Installation" section).

➄

Run electrical wiring (see "Electrical Connections," page 2).

➅

Set limits (see "Adjustments," page 2).

➆

Re-install headbox cover.

Figure 5

➉

Run electrical wiring (see "Electrical Connections," page 2), and set limits

(see "Adjustments," page 2).

Figure 4

Caution: Be sure motor is fully

re-seated in the bracket, and

re-secured carefully with the

motor retaining spring.

Page 109 of 120

1 2 ... 104 105 106 107 108 109 110 111 112 113 114 ... 119 120

Kommentare zu diesen Handbüchern

Keine Kommentare

Draper SC1 Bedienerhandbuch Seite 109

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Draper SC1