Draper SC1 Bedienerhandbuch PDF herunterladen (Seite 42)

Please Note

➀ Make sure power is disconnected before installing controls.

➁ SGC4 is a line voltage control, designed to operate up to 4 motors as a

group, activated by Low Voltage input commands.

➂ SGC4 enclosure is 8" x 8" x 4".

➃ Main Disconnect and Branch Circuit Protection provided by installer.

➄ Maximum surrounding air temperature 50° C.

➅ Use copper conductors rated 75 degrees Celsius or higher only, 18-

12AWG.

Electrical Speciﬁ cations

Input:

Data: +5v AC BUS Commands

Low Voltage: Dry Contact—0v AC

Line Voltage: 115v AC +/- 10%

Output:

115v AC Largest Motor 1FLA, 4FLA Total

Wiring Instructions

™

SGC4 Control by Draper

If you encounter any difﬁ culties installing/wiring your IntelliFlex control, call your

dealer or Draper, Inc., Spiceland, Ind., (765) 987-7999; or fax (765) 987-7142.

Part Number C156.059

E258229

All connection wires must conform to the motor manufacturer’s

recommendation and prevailing electrical codes. The switch and control

system wires should be at least 24 AWG and no larger than 18 AWG.

Please Note:

All input devices (low voltage LED switches, IR eye, RF receiver) which

connect to the Eye jack must be connected using electrically straight 4-

conductor modular cable (RJ11). This means colors do not cross over: blue

leads to blue, orange to orange, etc. (see diagram below)

If you use standard telephone cable, you must ﬁ rst remove one connector,

turn it over and re-attach, to ensure that the cable is electrically straight (see

diagram below).

Yellow

Red

Green

Black

Yellow

Red

Green

Black

Yellow

Green

Red

Black

Yellow

Green

Red

Black

Standard Telephone Cable

(Before, will not work)

Telephone Cable After

(Electrically Straight-will work)

Yellow

Green

Red

Black

Yellow

Green

Red

Black

Electrically Straight Data Cable

Using Telephone Cable

Fabric un roll ing from back of

roller (standard)

Fabric unrolling from front of

roller (reverse roll)

Interior

side

Interior

side

Right hand motor

(Standard)

Black—Up

Red—Down

Left hand motor

Black—Down

Red—Up

Right hand motor

(Standard)

Red—Up

Black—Down

Left hand motor

Red—Down

Black—Up

Please Note: This device has not been evaluated for reliability to the

Standard for Tests for Safety-Related Controls Employing Solid-State

Devices, UL 991 and therefore not considered suitable for entrapment

protection.

IntelliFlex

White (Neutral)

Black (Up)

Red (Down)

Connect all

Grounds

Here

Neutral

AC (115V AC)

DO NOT USE

Programmable Dry

Contact Inputs:

This can be any

Single Pole, Double

Throw switch

Com

Down

Aux Port: Out to

next IntelliFlex motor

control Aux or Eye port

Eye Port: In

from previous

Aux port or

input device

To Eye Port

To Switch,

splitter or

other input

device

White (Neutral)

Black (Up)

Red (Down)

Motor

White

(Neutral)

Black (Up)

Red (Down)

Motor

White (Neutral)

Black (Up)

Red (Down)

Motor

White

(Neutral)

Black (Up)

Red (Down)

Motor

Ground

115V

Inserting wire into spring terminal

➀ Open spring terminal by inserting screw-

driver into upper opening.

➁ Insert wire into lower opening.

➂ Remove screwdriver.

Right hand motor

(Standard)

Max of 100 feet

of low voltage-

cable between

controls, or

control and

input with circuit

board.

Note: Motor red and

black wires will need

to “ﬂ ip” if one motor

is right hand and the

other is left hand.

Page 42 of 120

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 119 120

Kommentare zu diesen Handbüchern

Keine Kommentare

Draper SC1 Bedienerhandbuch Seite 42

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Draper SC1