Draper SC1 Bedienerhandbuch PDF herunterladen (Seite 49)

Installation Instructions

™

RF Remote Control by Draper

➀

The Radio Frequency receiver must be connected to an Eye Jack on

an SC1 or splitter.

➁

Mount receiver with the antenna pointing up.

➂

Do not mount receiver on or near a metal surface.

➃

Each RF receiver must be “trained” to “hear” each transmitter before

it will work.

➄

Each receiver can “learn” to “hear” up to ﬁ ve different transmitters.

Eye

Aux

SC1

"Silver Satin" 4-conductor

Flat Modular Phone Cable

must not "flip"

(i.e., black is always on left).

FOR HOME OR OFFICE USE

This Class B digital apparatus meets all

requirements of the Canadian Interference-

Causing Equipment Regulations.

To Eye Por t

on SC1

Program

Mode

Press to Learn

Transmitter

Tested to Comply

With FCC Standards

SC1

Installing the Receiver

RF Handheld Transmitters

ALL

OPEN CLOSE

STOP

Connect the receiver to the Eye Jack on an SC1 or splitter (see Fig. 1). If

the eye connects to a splitter, then the Main Jack of the Splitter must connect

to the Eye Jack of an SC1.

Mount the receiver with the antenna pointing up. For longer range

reception, detach the provided antenna and attach the optional Long Range

Antenna—Part # C267.001 (see Fig. 2).

Please Note: For information on installing SC1 or other “BUS” command

controls, please see the instruction sheet for the appropriate item.

Training Your RF Receiver

The receiver can “learn” up to 5 different transmitters. It ships from the

factory with NO transmitters learned: you must train it in the ﬁ eld to work with

your speciﬁ c transmitters. If the receiver is new with no transmitters learned,

the LED will automatically come on when plugged into an “Eye” port.

➀

Press and release the “Learn Transmitter” button on the receiver. The red

LED will come on if 5 transmitters have not already been learned. The unit

is now ready to learn another radio transmitter.

➁

Press any button on the radio transmitter. The LED on the receiver will go

out. This transmitter is added to the list of known transmitters. The

receiver returns to normal operation after it has learned a transmitter. If

this transmitter is already known to the receiver, the LED will remain lit

because the transmitter does not need to be learned again.

If no command is received within 10 seconds:

➀

The red LED will ﬂ ash off, then on, and then go out. No new transmitters

were learned.

➁

If no transmitters are known, the LED will turn back on immediately.

If the red LED is on and the learn button is pressed and released:

➀

The red LED will turn off with no changes to the learned list.

➁

If no transmitters are known, the LED will turn back on immediately.

Figure 1

Figure 2

If no transmitters are known (factory default):

➀

The red LED will turn on as soon as the unit is powered.

➁

The red LED will ﬂ ash every 10 seconds until a transmitter is learned.

➂

Pressing the learn button has no meaning while in this mode (the LED will

turn off while the button is pushed).

To clear all known transmitters:

➀

Press and hold the learn button for 5 seconds. The red LED will blink on

and remain on, until a new transmitter is learned.

➁

Release the button, the red LED will come on. The unit is ready to learn

the 1st transmitter.

Please Note: If you press and release the learn button and the red LED does

not come on, the list may be “full” and no more transmitters can be learned.

The unit may also not be powered correctly—to ﬁ x this, clear receiver and

start over.

The receiver will not pass commands to the SC1:

➀

While in the learn mode (the red LED is on).

➁

While the button is pressed.

Please Note: The stop command will be sent to the SC1 system if the

transmitter’s STOP button is still pressed when the receiver exits from learn

mode after learning the transmitter.

Installing the RF Keypad or Wall Switch

If using an RF Wall Mounted Keypad or RF Wall Switch, ﬁ rst test for reception

and successful operation of the switch in the desired location. Then, cut hole

in appropriate location, attach transmitter module to switch or keypad using

modular cable, and attach switch to wall.

Please see Fig. 3 (below), and information provided with the speciﬁ c switch or

keypad for more information. Three AAA batteries required.

Figure 3

Please see page 2 for

information on radio

frequencies and codes.

If you encounter any difﬁ culties installing/wiring your IntelliFlex RF control, call your

dealer or Draper, Inc., Spiceland, Ind., (765) 987-7999; or fax (765) 987-7142.

Please Note:

For button press sequences to manually

program your control, see “SC1 Quick Ref-

erence Guide” at www.draperinc.com

Page 49 of 120

1 2 ... 44 45 46 47 48 49 50 51 52 53 54 ... 119 120

Kommentare zu diesen Handbüchern

Keine Kommentare

Draper SC1 Bedienerhandbuch Seite 49

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Draper SC1