Draper SC1 Bedienerhandbuch PDF herunterladen (Seite 36)

Wiring Instructions

™

Isolating Relay by Draper

Wiring Diagram of more than one Isolating Relay Daisy-Chained

Part Number C157.012

Please Note

➀ Make sure power is disconnected before installing controls.

➁ This product is designed to be a job site rescue device by allowing multiple motors

to be connected to one motor control or switch and provides group control of

these motors. Each motor must have its own ISO Relay. Make sure the total FLA

of all motors grouped together does not exceed the load carrying capacity of the

switch or motor control being used.

➂ When installing an ISO into an enclosure, maintain a minimum of .2" (5mm)

spacing in all directions using the supplied spacers. An insulator plate should also

be used. Shorts will result in damage to the component.

➃ All metal traces may have AC power on them and must be insulated from the user

and from electrical ground. An INS-ISO (Draper Part# C199.004) insulation

board is provided.

➄ Large black part may have a small voltage on it immediately after unit is active.

➅ To achieve Pollution Degree 2 environment, mount in an enclosure with tight ﬁ tting

seams or one that is gasketed.

➆ The Main Disconnect and Branch Circuit Protection shall be provided by installer.

Protection for shade motor must be provided at the switch or breaker panel.

➇ Maximum surrounding air temperature 70 degrees Celsius.

➈ Use copper conductors rated 75 degrees Celsius or higher only, 18-12AWG.

Please Note: This device has not been evaluated for reliability to the Standard

for Tests for Safety-Related Controls Employing Solid-State Devices, UL 991

and therefore is not considered suitable for entrapment protection.

Electrical Speciﬁ cations

Input:

Line Voltage: 115v AC +/- 10%

Output:

115V AC 5 FLA

(For a wiring diagram of more

than one Isolating Relay Daisy

chained together, see below)

E225537

20HN

Inserting wire into spring terminal

➀ Open spring terminal by inserting screw-

driver into upper opening.

➁ Insert wire into lower opening.

➂ Remove screwdriver.

Dims: 2.07" L x 1.41" W x 0.82" H

(52.6 x 35.8 x 20.8 mm)

1 Isolating Relay ﬁ ts in a standard

single gang J-Box.

From Motor:

White-Neutral

Motor Up

Motor Down

Neutral

Down

To switch

and/or next

ISO 115

If you encounter any difﬁ culties installing/wiring your IntelliFlex control, call your

dealer or Draper, Inc., Spiceland, Ind., (765) 987-7999; or fax (765) 987-7142.

110-120V AC

Motor 1

Green

INPUT

110-120V AC

Motor 2

Green

Neutral

Down

Note:

Motor red and black

wires will need to

"flip" if one motor

is right hand and the

other is left hand.

Motor Neutral

Black - Up

Red - Down

115V AC

Hot

Neutral

This can be

any Single Pole,

Double Throw switch

additional

ISOs

Earth

Ground

Neutral

Down

Additional

Motor

Green Wire

ISO

Fabric un roll ing from back of

roller (standard)

Fabric unrolling from front of

roller (reverse roll)

Interior

side

Interior

side

Right hand motor

(Standard)

Black—Up

Red—Down

Left hand motor

Black—Down

Red—Up

Right hand motor

(Standard)

Red—Up

Black—Down

Left hand motor

Red—Down

Black—Up

Page 36 of 120

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 119 120

Kommentare zu diesen Handbüchern

Keine Kommentare

Draper SC1 Bedienerhandbuch Seite 36

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Draper SC1